Fuselage Kit Options, Sport Trainer Kit

Kit includes these fabricated components, stabilizer attach brackets, stringer attach brackets, throttle attach brackets, ELT mounting plate Mag switch plate, rear window frames, torque tube bracket assy., floor board attach brackets, rudder pedal clamps, jack screw pedestal, aileron cable guards, landing gear attach fittings, spar attach fittings, front window supports, front window inside fairing, tail spring attach bracket, tail wire fittings, elevator bell crank mounts, elevator horn insp. plate, stringer attach clips, wood stringer kit, fuselage step, fuselage handle, finish welded bird cage also includes raw materials 4130 chromoloy tubing, and channeling to construct the fuselage.

90 - feet, 3/4” x .035 4130N Tubing
75 - feet, 5/8” x .035 4130N Tubing
25 - feet, 1/2” x .035 4130N Tubing
36 - feet, 7/8” x .049 4130N Tubing
13 - feet, 1” x .049 4130N Tubing
  3 - feet, 1-1/8” x .058 4130N Tubing
13 - feet, 5/8” x .049 4130N Tubing
12 - feet, 3/4” x .049 4130N Tubing
  5 - feet, 3/8” x .035 4130N Tubing
  5 - feet, 5/16” x .028 4130N Tubing
  3 - feet, 7/8” x .058 4130N Tubing,
  1 - foot, 1/2” x .065 4130N Tubing (engine mount bushings)
  1 - foot, 3/8” x .035 4130N Tubing (fairlead standoff)
  1 - foot, 3/4” x 3/4” Square Tubing
  1 - foot, 3/8” x .065 4130N Tubing
  1 - pair, Stabilizer Attach Bracket, RH & LH 
  2 - Fuselage Channel, 48’
14 - Stringer Attach
  3 - pieces, Baggage Attach Material, 1/2” x 1/2” x 1/2” x 36”
  2 - Preformed Upper Side Stringer Attach Bracket
  1 - Preformed Top Stringer Attach Bracket
  2 - Throttle Attach Bracket
  1 - Mag Switch Plate
  1 - Fuselage Handle, 9”
  2 - Rear Window Frame
  1 - Torque Tube Bracket Assembly, Front
  1 - Torque Tube Bracket Assembly, Rear
  1 - set of 20 pieces, Floorboard Rudder Attach Brackets & Clamps
  1 - Aileron Cable Guards, LH
  1 - Aileron Cable Guards, RH
  2 - Landing Gear Fitting, Rear
  2 - Landing Gear Fitting, Front
  1 - Front Spar Attach Fitting
  2 - Rear Spar Attach Fitting, LH & RH (1 of each)
  1 - Torque Tube Aileron Stop Assembly, LH
  1 - Torque Tube Aileron Stop Assembly, RH
  2 - Front Window Supports, 1-3/4” x 3/8” x 24”
  2 - Front Window Inside Fairing
  1 - Tailspring Fitting
  1 - Step
  1 - pair, Tailbrace Wire Fittting
  1 - Elevator Bellcrank Mount, LH
  1 - Elevator Bellcrank Mount, RH
  2 - 10’ Wood Stringer
  3 - 12’ Wood Stringer
40 - Stringer Attach Clips
  1 - pair, Elevator Horn Inspection Plates, RH & LH
  1 - Jack Screw Pedestal Assembly
  4 - Engine Mount Attach Bushing Washer
  1 - Tailpost Assembly
  2 - 1/2” x 1/2” x 11/8” 16 Gauge Channel
  1 - set, LH Sliding Window Guide Assembly
  1 - pair, Fairing Channels (elevator horn)
  1 - Birdcage
  1 - AN970-6 Washer
  1 - 2 + 2 Window Track
  1 - Step Clamp
12 - Rudder Cable /Trim Tab Fairlead Tubes

Code 8