Fuselage Kit Options, Super Sport Kit, Non-PMA'd

Fuselage-materials kit includes these fabricated Components Stabilizer attach brackets, Stringer attach brackets, Throttle attach brackets, ELT mounting plate Mag switch plate, Rear window frames, Torque tube bracket assy., Floor board attach brackets, Rudder pedal clamps, Jack screw pedestal, Aileron cable guards, Landing gear attach fittings, Spar attach fittings, Front window supports, Front window inside fairing, Tail spring attach bracket, Tail wire fittings, Elevator bell crank mounts, Elevator horn insp. plate, Stringer attach clips, Wood stringer kit, Fuselage step, Fuselage handle, finish welded bird cage also includes these Raw materials 4130 chromoloy tubing, and channeling to construct the fuselage.

90 - feet, 3/4” x .035 4130N Tubing
76 - feet, 5/8” x .035 4130N Tubing
25 - feet, 1/2” x .035 4130N Tubing
36 - feet, 7/8” x .049 4130N Tubing
14 - feet, 1” x .049 4130N Tubing
  3 - feet, 1-1/8” x .058 4130N Tubing
13 - feet, 5/8” x .049 4130N Tubing
12 - feet, 3/4” x .049 4130N Tubing
  6 - feet, 3/8” x .035 4130N Tubing
  5 - feet, 5/16” x .028 4130N Tubing
  3 - feet, 7/8” x .058 4130N Tubingt
  1 - foot, 1/2” x .065 4130N Tubing (engine mount bushings)
       3/8” x .035 4130N Tubing (fairlead standoff)
  7 - feet, 3/8” x .065 4130N Tubing
  1 - pair, Preformed Elevator Horn Inspection Plate, LH & RH
  1 - Elevator Bellcrank Mount, LH
  1 - Elevator Bellcrank Mount, RH
  1 - pair, Fairing Channels
  1 - Fuselage Handle, 9”
  2 - Rear Window Frame 2
  1 - Torque Tube Bracket, Front
  1 - Torque Tube Bracket, Rear
  1 - set of 20 pieces, Floorboard Rudder Attach Brackets and Clamps 
  2 - Landing Gear Fitting, Rear
  2 - Landing Gear Fitting, Front
  1 - Spar Fitting, Front
  2 - Spar Fitting, Rear, RH & LH (1 of each)
  1 - Tailspring Fittings
  1 - Step
  1 - pair, Tailbrace Wire Fittings
  1 - 10’ Wood Stringer
  3 - 12’ Wood Stringer
  1 - pair, Stabilizer Support Bracket, LH & RH
  1 - foot, 3/4” x 3/4” Square Tubing
  2 - sets, Fuselage Channeling, 48’
14 - Stringer Attach
  3 - pieces, Baggage Attach Material, 1/2” x 1/2” x 1/2” x 36”
  2 - Preformed Upper Side Stringer Attach Brackets
  1 - Preformed Top Stringer Attach Bracket
  2 - Throttle Attach Bracket
  1 - Mag Switch Plate
  1 - Aileron Cable Guards, RH
  1 - Aileron Cable Guards, LH
  1 - Torque Tube Aileron Stop Assembly, LH
  1 - Torque Tube Aileron Stop Assembly, RH
  2 - Front Window Supports, 1-3/4” x 3/8” x 24”
  2 - Front Window Inside Fairings
  1 - Jack Screw Pedestal Assembly
  4 - Engine Mount Attach Bushing Washer
  1 - Tailpost Assembly
  2 - each, 1/2” x 1/2” x 11/8” 16 Gauge Channel
  1 - set, LH Sliding Window Guide Assembly
  1 - Birdcage
  1 - Header Tank Bracket, LH
  1 - Header Tank Bracket, RH
  1 - AN970-6 Washer
40 - Stringer Clamp
  1 - 2 +2 Window Track
  1 - Step Attach Bracket
12 - Rudder Cable/Trim Tab Fairlead Tubes

Code 8